How to install the function of door stopper

2022-07-22
  • Detail

In life, although door stopper is a small thing, it is still very useful. It can prevent the door from hitting the wall and shaking at will, so the door suction is small but powerful. Moreover, the door stopper installation cannot be sloppy, because it is still a moving part, which should bear the impact and pull of the wooden door, and the stress of the wall and floor tiles that fix it. In addition, the impact on the door should also be considered. Therefore, the installation quality of the door stopper is directly related to the door, wall, floor, floor tiles, and personal safety

in life, although door stopper is a small thing, it is still very useful. It can prevent the door from hitting the wall and shaking at will, so the door suction is small but powerful. Moreover, the door stopper installation cannot be sloppy, because it is still a moving part, which should bear the impact and pull of the wooden door, and the stress of the wall and floor tiles that fix it. In addition, the impact on the door should also be considered. Therefore, the installation quality of the door stopper is directly related to the door, wall, floor, floor tiles, and personal safety. The following editor will introduce how to install the door stopper and its functions

how to install the door stopper

first, determine whether the door stopper is installed on the wall or on the floor

it depends on the actual situation

second, test and determine the position of the door stopper

open the door to the maximum position, preliminarily determine the position of the door stopper, open the door, adjust the position of the door stopper, and use the method of fine-tuning up, down, left and right until the appropriate position and angle are reached. During the final test, open the door to the maximum and determine its position

third, if it is installed on the ground, it needs to be limited to the fixed position of the door, and then make final confirmation on the opposite side, make a mark

underline to confirm that the door is opened to the maximum position. Finally, determine the installation position of the door stopper

fourth, draw the positioning position of the door stopper

according to the above tests, it is best to locate the position of the door stopper twice, which is mainly convenient for installation. In order to better confirm the angle of door suction and opening

fifth, use a drill to drill at the installation position of the door suction

such as drilling the installation hole of the door suction on the ground

sixth, assembly of the fixed end of the door stopper

install the fixed end of the door stopper and screw in the screws

seventh, fix the door stopper on the ground (this step requires professional experience)

screw the screws with a small internal angle, confirm the position, drilling and assembly procedures again, and then install the fixed end on the ground. Tighten the screws on the fixed end with the attached internal angle gadget, and the door stopper will be installed automatically

eighth, the determination of the position of the door stopper

the door stopper end on the door only needs to be screwed down. After both ends of the door stopper are installed, it should be almost done. The most important thing is to test, open the door until drunk, then find the position of the door stopper on the door, and screw down the door stopper at the door end with screws

ninth, fine tune

the last step is to rotate the angle of the door stopper, fine tune it to fit all the door stopper at the door end, and finally completely tighten the screws

the function of the door stopper

the door stopper is composed of two parts: a suction plate and an electromagnet, which keep the fire door normally open and release automatically in case of fire. The fire door closes automatically under the action of the door closer, and the closing signal is fed back to the fire control center to play " Movable fire separation " Function to meet high requirements

the biggest use of door suction is to prevent the door from closing due to external forces such as air flow or accidental human touch. Unexpected door closure often leads to two problems: being locked out; Bruise the person who is entering or leaving the door

types of door stopper

1. Door stopper is divided into permanent magnet door stopper and electromagnetic door stopper. Permanent magnet door stopper is generally used in ordinary doors and can only be controlled manually; Electromagnetic door suction is used in electrically controlled door and window equipment such as fire doors, which has both manual control and automatic control functions

2. The ordinary permanent magnet door stopper is divided into wall mounted type and ground mounted type according to the installation form, and plastic type and metal type according to the material; According to different installation methods, the products of electromagnetic door suction are divided into three categories: ct-01 wall type, ct-02 floor type and ct-03 chain type. According to different structures, wall electromagnetic door suction is divided into standard type, increased type, extended type, box type, concealed type, long arm type, etc; The ground electromagnetic door stopper is composed of ct-01 wall electromagnetic door stopper and right angle ground mounting bracket; Chain electromagnetic door stopper is composed of ct-01 wall electromagnetic door stopper and chain fastener; Since the main bodies of ct-01 wall type, ct-02 floor type and ct-03 chain type electromagnetic door suction are common to each other, it is convenient for users to use them according to the installation conditions on the use site

editor's summary: that's all for how to install the door stopper and its functions. I hope it will be helpful to you. If you want to know more, you can pay attention to information

贵阳男科医院

武汉癫痫医院

太原妇科医院

Copyright © 2011 JIN SHI